Keypad lock in St. Mary's
Tom Hanks, owner, 24/7 Express Handyman Service · Updated September 2026
24/7 Express Handyman Service installs keypad locks in St. Mary's. 2-1/8 or 1-1/2 inch door holes and a 2-3/8 or 2-3/4 inch backset are what a Kwikset touchscreen deadbolt is made to fit. (Kwikset 275 Touchscreen Electronic Deadbolt Installation and User Guide) In 1926 the four-story St. Mary's of the Wasatch Catholic school complex was built on Salt Lake City's east bench, and it dominated the skyline below the golf course for many years. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014)) In the Salt Lake City & Millcreek zone, scheduled work is $95/hour with a 2-hour minimum and no dispatch fee, plus a $15 fuel surcharge.
How much does a keypad lock job cost in St. Mary's?
From $205
Keypad lock in St. Mary's starts at $205: the 2-hour minimum at $95/hour ($190) plus the $15 fuel surcharge, with no dispatch fee. Time past 2 hours is billed in 30-minute steps. Larger parts are billed at cost plus 25%.
Call now
Salt Lake City & MillcreekAnswered 24/7 by Tom or his dispatcher.
Dispatch fee $199–$349 by time of day, due on arrival, covering the first hour on site. After that, $150/hour in 30-minute steps. Fuel surcharge $15. Supplies fee $50. Full price sheet and estimator
Typical arrival in the Salt Lake City & Millcreek zone: 60–90 minutes.
24/7 Express Handyman Service confirms the address, the zone rate and the dispatch fee, and takes a card, before rolling.
What 24/7 Express Handyman Service does on site
- Installs battery-powered keypad and smart deadbolts in existing door preps, or bores new holes to the lock maker's template.
- Adjusts the strike and latch so the bolt throws fully without the door being pushed or lifted.
- Sets up the master code with the owner and tests every code, the physical key and the battery backup before leaving.
How it works
- The owner picks the lock, and the door thickness, hole size and backset are measured to confirm it fits.
- The door prep, strike alignment and install are priced in writing.
- The lock is installed, the strike is adjusted, and the door is tested from inside and out.
- Referred out: hardwired access systems, doorbell wiring and any new electrical work.
What happens next
- The written scope and price come first; the owner sets or confirms the codes at the end of the visit.
- Photograph the damage before anything is moved and keep every receipt; 24/7 Express Handyman Service provides an itemised invoice your insurer may ask for. The dispatch fee and job cost are paid by you on the day.
In St. Mary's
The neighborhood around St. Mary's Way is an eclectic mix of custom-designed homes dating from the 1950s to the 1970s, with a golf course to the north. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014)) On May 29, 1952, a subdivision plat was filed for an area at the southeast corner of the golf course, and the resulting Oak Hills Plat A-1 included 32 lots on St. Mary's Way, Bonneville Drive and Oak Hills Way. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014)) A National Register-nominated house on St. Mary's Way is fully integrated with its sloping site, built on a concrete foundation and clad in striated brick veneer with matching brick retaining walls, planters and patios. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014))
Calls come from around Bonneville Golf Course, Utah's Hogle Zoo, This Is The Place Heritage Park.
Every job 24/7 Express Handyman Service takes on is under $3,000 including labor, materials and any change orders (Utah Code §58-55-305); a change that would push a job over that line is referred to a licensed contractor, not written up as a second job. plumbing, electrical, HVAC, gas appliance / combustion system work is referred to a licensed trade.