Plaster hanging in St. Mary's
Tom Hanks, owner, 24/7 Express Handyman Service · Updated September 2026
24/7 Express Handyman Service hangs heavy items on plaster in St. Mary's. 3/4 to 7/8 inch is the usual total thickness of plaster over old wood lath, per the National Park Service. (Preservation Brief 21: Repairing Historic Flat Plaster: Walls and Ceilings (National Park Service)) In 1926 the four-story St. Mary's of the Wasatch Catholic school complex was built on Salt Lake City's east bench, and it dominated the skyline below the golf course for many years. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014)) In the Salt Lake City & Millcreek zone, scheduled work is $95/hour with a 2-hour minimum and no dispatch fee, plus a $15 fuel surcharge.
How much does a plaster hanging job cost in St. Mary's?
From $205
Plaster hanging in St. Mary's starts at $205: the 2-hour minimum at $95/hour ($190) plus the $15 fuel surcharge, with no dispatch fee. Time past 2 hours is billed in 30-minute steps. Larger parts are billed at cost plus 25%.
Call now
Salt Lake City & MillcreekAnswered 24/7 by Tom or his dispatcher.
Dispatch fee $199–$349 by time of day, due on arrival, covering the first hour on site. After that, $150/hour in 30-minute steps. Fuel surcharge $15. Supplies fee $50. Full price sheet and estimator
Typical arrival in the Salt Lake City & Millcreek zone: 60–90 minutes.
24/7 Express Handyman Service confirms the address, the zone rate and the dispatch fee, and takes a card, before rolling.
What 24/7 Express Handyman Service does on site
- Find the studs and lath behind plaster before choosing a fastener for mirrors, art, shelves and coat racks.
- Drill through tape with a masonry bit so the plaster doesn't crack or chip around the hole.
- Use screws long enough to reach through the plaster into framing, or toggles sized for thick hollow walls.
How it works
- Weigh the item and decide whether it needs a stud or can hang from the lath.
- Locate framing with a magnet or small test holes, then mark and tape the drill points.
- Pre-drill, set the fasteners, hang the piece and check that it is level and tight.
- Referred out: loose, bulging or delaminated plaster that needs reattaching or replastering goes to a plaster contractor.
What happens next
- The written scope and price come first; what's being hung, where, and the fastener for each piece are agreed before any drilling.
- Photograph the damage before anything is moved and keep every receipt; 24/7 Express Handyman Service provides an itemised invoice your insurer may ask for. The dispatch fee and job cost are paid by you on the day.
In St. Mary's
The neighborhood around St. Mary's Way is an eclectic mix of custom-designed homes dating from the 1950s to the 1970s, with a golf course to the north. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014)) On May 29, 1952, a subdivision plat was filed for an area at the southeast corner of the golf course, and the resulting Oak Hills Plat A-1 included 32 lots on St. Mary's Way, Bonneville Drive and Oak Hills Way. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014)) A National Register-nominated house on St. Mary's Way is fully integrated with its sloping site, built on a concrete foundation and clad in striated brick veneer with matching brick retaining walls, planters and patios. (National Register of Historic Places Nomination: John & Margaret Price House, 2691 E. St. Mary's Way (SLC Historic Landmark Commission memo, 2014))
Calls come from around Bonneville Golf Course, Utah's Hogle Zoo, This Is The Place Heritage Park.
Every job 24/7 Express Handyman Service takes on is under $3,000 including labor, materials and any change orders (Utah Code §58-55-305); a change that would push a job over that line is referred to a licensed contractor, not written up as a second job. plumbing, electrical, HVAC, gas appliance / combustion system work is referred to a licensed trade.